Machine works fine, but I can only program it by typing out the Gcode manually in the machine. Which is a real PIA!

Jan 11, 2018 - N Xilog Maestro 2 - You. Where can I find Xilog software? Looking to find out where I can download xilog3 or xilog plus to be used with my SCM.

From what research ive done apparently Xilog is the appropriate software to use with this machine? I wanna be able to program comfortably on my laptop then transfer to machine either via floppy or network. Writing a program manually in gcode line for line at the machine just way too time consuming.

So hopefully Xilog is the answer to my woes? If not maybe you can point me in the right direction. From what I can tell I must only have the machine control half of the software, and not the program editing half. I have the control software on the machine which allows the setup of tools, Gcode editing/loading, manual control ect. But I dont have anything to create/edit programs on a separate computer. So I have been resorting to just plotting out tool paths in gcode right in the machine control panel.

It is shown that the value of the germination indices within the time of the grain storage increases achieving maximum in 9 months. • 45 Downloads Abstract Changes were studied that occurred during storage in the grain of the spring two-row barley of Get’man and Priazovskii 9 breeds permitted to use in the North Caucasian region and their influence on the malt quality. Ermolaeva spravochnik rabotnika laboratorio pivovarennogo predpriyatiya. The germination index of Get’man breed was higher than in Priazovskii 9 breed. Both breeds had low water sensitivity within the whole storage period. In the malt obtained from the grain stored for more than 6 months, the content of protein reduced.

Its getting me by, but as you can imagine its a big hassle.If I wanna change the size of a part I have to completely go through my code line by line, as where this Xilog editing software should have some sort of parametric ability. But I dont know, old machine and documentation is hard to come. I havent talked to SCM, yet. I guess I didnt think they would be much help since this is an old machine I purchased used at auction. Worth a try I suppose.

Xilog Plus (Just unpack to root. Editor - XilogPlus/Bin/Parsifal.exe. Its 'standard' Xilog Plus for SCM Tech. Before writing programms, you must open and edit def.tlg file. I think, you old machine will not work with pgm files. You will need convert *.pgm to *.xxl with winxiso.exe (folder Bin).

Update: I found only one T99 with Xilog3 in our archive. Try this: Xilog 3 (Same procedure, unpack to root, run Xilog3.exe P.S. Any Xilog will not work under 64bit OS. Thank you very much!

I found the serial number for my machine, it is AL1-001909 When I write a program in editor and save it to the machine, it is in the PGM format already. The machine has something called esacad on it which seems to be some kind of graphical programming interface. It is very basic in functionality from what I can tell, I played with it only a little bit though. I have absolutely no documentation on this esacad and find even less on the net.

But either way with Xilog plus I should be able to do what I need. Auckcabs, I working for the SCM Group in Brazil(SCMTecmatic) and say for you load Software Tria and Parametrs and data of PLC not is easy the work. But you can try, you need the all data and Floppy Drives formated in the macchine. Only in this way will you be able to get a bit of success in this endeavor. The phone number of our service in Italy is: +39 0541 700100. Probably you will be directed to the support of coach Sir Giuseppe Andreani or Montanari Because your machine is already an old machine and few know her to be able to support. Where machine is installed?

What Country and City? Sorry for my English.

If you speak Italian or Spanish I would prefer because it could express myself better. So that you fully understand me. Enviado do meu iPhone usando o Tapatalk. We are a little carpenter's workshop (3 coworkers) and we have purchased an old machine at auction module.

We had expectations improving our productivity, but sincerely, we have no idea how we could optimize times programing our machine out of TRIA7500. We can only program it by typing out the manually in the machine consuming excessive time. Is Xilog the appropriate software to be able to program our machine in an easier way?

Where could find the necessary software? How to install Xilog on my PC? Do exist a manual or tutorial for Xilog?

Is it necessary to downgrade the OS to 32bits in order to use Xilog? Thank you in advance!

Machine: Morbidelli 503 Year: 1997 Serial Number: AL3514. @AntonioC We purchased the A213 (tria7500) a while back on auction and took me 2 months and countless hours on the net to figure this out. For our NC, xilog and xilog plus does not work as the NC does not recognise the.PGM file format.

This is how we resolved it: 1. We open the.DXF file in Aphacam and save it as.ANC file.

We rename the.ANC file to.TXT file 3. Then we use the CN75NEW.exe file, run in DOS mode to convert the.TXT file to.PGM 4. We then send the file via NULL-MODEM cable to NC 5. Open the file in EDITOR on NC and verify it. Hope this helps.send me an email if you require more info or any of the files etc:) mail at aucklandcabinets dot co dot nz.

Hola muy buenas, yo tambien tengo el mismo problema, estoy buscando el xilog para poder programar en mi ordenador portatil y luego pasarlo a la maquina, pudiste encontrar el xilog en algun lado saludos Thank you very much! I found the serial number for my machine, it is AL1-001909 When I write a program in editor and save it to the machine, it is in the PGM format already. The machine has something called esacad on it which seems to be some kind of graphical programming interface. It is very basic in functionality from what I can tell, I played with it only a little bit though. I have absolutely no documentation on this esacad and find even less on the net. But either way with Xilog plus I should be able to do what I need.